Commercial Tiling Contractors

Yes, but there are a few things to think about first. Professionals will examine if the walls can support the additional weight, as well as whether the present tiling has a solid grip on your walls or floor.

This indicates that the floor was not properly prepared. It’s a common occurrence that may be prevented by using a trustworthy tiler. Before you start tiling, make sure your flooring are fastened down, then cover them with a layer of cement board that is screwed every six inches in all directions. Then, to allow for expansion in the timber underneath, a decoupling membrane should be placed. Then you may start tiling on top of it. It’s important to remember that if you can see or hear something moving (creaking), it’s not ideal for tiling.

Porcelain tiles are incredibly durable, making them ideal for use on floors. Over the last 10 years or so, they’ve been the most popular option. They’re difficult to cut and drill, but any seasoned tiler will have the right equipment to get the job done.

Yes, however keep in mind that they’ll be exposed to the elements outside and will need to be non-slip. I would always recommend a high-quality porcelain tile since they are extremely durable and come in a variety of non-slip finishes.

This is the result of shoddy installation. Tiles should only be installed on a strong adhesive bed. It’s not enough to dab a dollop of glue over the tile’s corners and push it against the walls or floor. To ensure that the glue is evenly disseminated under the surface, your tiler should utilise a notched trowel.

Without a doubt. To allow any cracks to form, heated screeds should be turned on two weeks before tiling begins. Because heated screeds shrink and expand somewhat during hot and cold cycles, you’ll need to use a decoupling membrane to prevent this. These can significantly increase the expense of your tiling, but they are definitely necessary for this procedure.

Tile is typically measured in square metres for both walls and floors (M2). One square metre is equal to one metre in length and one metre in breadth. If you’re tiling a wall that’s 2.4 metres high by 2 metres wide, multiply the length by the width to get 4.8 metres squared. Rep for each wall or floor you’re tiling, adding 15% to the total to account for waste and off cuts. This will generally provide you with enough tiles to complete the project. Use our tile calculator to figure out how many tiles you’ll need automatically.

Yes, removing a damaged or chipped tile and replacing it with a new one is rather straightforward.

You’ll need a replacement tile first, which might be tricky if you don’t have one from the previous installation. Then carefully shatter the broken tile with a hammer and remove the fragments with an old chisel, taking careful not to damage the good tiles surrounding it.

Natural stones such as slate, marble, travertine, and limestone must be cut using a wet cutting machine rather than a typical score and snap tile cutter, which takes much longer and requires work outside. They must also be sealed before and after grouting, which will lengthen the process.

When selecting new tiles for your floors or walls, you’ll need to consider a number of factors. They must be long-lasting and blend well with the decor of each area. We’re always happy to offer free, expert advise on tiling projects.

Porcelain tiles are extremely long-lasting. They’re constructed of fine clay that’s been burnt at extremely high temperatures. They are denser than ceramic or marble tiles as a result of this. Our expert tilers have extensive expertise installing porcelain tiles and can assist you in selecting the best tiles for your project.

It is possible to apply new tiles over old ones. Before consenting to the approach, a skilled tiler will need to determine if your previous tiles are sufficiently adhered to your walls or floor.

Yes, they may be used outside, but bear in mind that they will be exposed to the elements. You’ll need to invest in non-slip tiles. Our knowledgeable tilers will gladly assist you in locating high-quality exterior tiles that fit your requirements.

This might be due to poor tile installation. It’s likely that the tiles were not installed on a solid bed of tile adhesive and that the coverage under the surface is uneven. Please contact us so that we can examine the issue and offer expert guidance.

Because each tile is unique, genuine stone is one of the most costly tile materials available. Second, the inherent imperfections on the tile surface necessitate the use of heavier tile adhesives during installation. We can assist you in locating excellent natural stone tiles.

It’s possible that the surface preparation was done wrong if your grout fractures. It’s possible that you’ll need to re-grout. An expert tiler can examine the condition and provide the finest grout repair suggestions.

You may rest confident that the tile work will be completely hidden. Tilers that work for Style Bathrooms are insured and follow all health and safety regulations.

From Monday to Saturday, including after-hours and on holidays, book your local tiling service in Dublin.

Don’t worry; the floor tilers will gladly provide you with free, helpful advise on any part of the situation.

Because the technicians are local and always on the move, you can count on flexing booking slots the same day or the next. Please keep in mind that last-minute service bookings are subject to availability.

Yes, all of the professionals are properly insured and adhere to all health and safety regulations, so you can be certain that the job will be covered.

Yes, this is a service we can do for you. Please bear in mind that the tradespeople will do an on-site survey in order to develop a customised strategy and deliver the outcomes you desire.